Standard in the firmware dd-wrt is a function of changes in link speed (10/100 mb/s) that shit is not working!
Because with this had to search a suitable solution is found:
The only utility audit port for dir-320, which fully works. It is possible to disable / enable the ports individually, translate the port in different modes (none | disable | block | listen | learn | forward), tagging, and velocity of the interface. Similar utilities such as ethtool and mII-tooles fail (stupidly did not work).
./robocfg port 3 media 10FD
thats make port 3 to 10 mbs. how its so easy. I'm using it because my cabble in not good.
In general, topic — the result of field tests of the relationship between the two routers, and my phone Nokia E51. The task was to establish communication at a distance of 1 km on the roofs of houses on the line of sight, before those tested in the field, maybe, to climb on theroofs of desire was not there.
Were taken two brand routers dir-320 from MTS. However, they absolutely do not differ from those that lie on the shelves except for a white body coated with these emblems of MTS special firmware from the developers of MTS for external usb 3G modem with the distribution of wifi ...
However firmware was pulled down and installed fairly well-known dd-wrt. (http://www.dd-wrt.com/)
All settings are standard on both, except that the first point, acting as an access point (A), second (B) is configured as a client to the first point, so that the client connects to A and B were all on the same LAN .
One of the most important moments of entogo — Antennas.
As the antenna was chosen because of ease of Double Biquad production availability of all necessary materials.
Needed: (one antenna)
— List of bilateral PCB 220×110
— Copper tube 4 cm (inner diameter slightly greater than the incoming cable into it)
— Copper wire 70 cm section of 1.5 mm
— Cable 70 ohm, 50 cm
— Any change in the form of plastic ties, tubes for securing the PCB design.
Manufacturing technology will not spread, it is here (http://martybugs.net/wireless/biquad/double.cgi)
The result should this:
In this case, they made it two for two routers.
Incidentally ... a small problem faced by the majority — connectors antennas to the router. I solved this problem ... so take a piece of wire from UTP. Bare and wound onto neogolennuyu chat turn to turn in a single layer ... it should be 6.5 turns ... now this «spiral» can be worn in the preload on the «nail» in size sockets router. the second piece of wire just pulls the top slot on the router. As a result, these two pieces of wire touches the cable from the antenna.
In field tests, point A was installed in the roof, the antenna is directed toward «the most distant woods.» The second point with the same antenna and MOBILE in a field.
Raises another problem — the power point, which is with itself. For meals were taken ordinary penlight batteries 4 pcs. Nutrition is just 1.5Vh4 = 6V when necessary 5B.
Next, what I would like to achieve — to go to such a distance in the line of sight to my Nokia on could catch the signal. What's most amazing and ridiculous for me it turned out — at a distance, I could not go right, maybe more was only the forest ...
Signal for a mobile phone on it showed the very same about 5-10 SNR. When you turn on the point, it successfully connects to another, even if the lapel antenna 90 degrees ... but why then the signal shows all the time in 92 SNR that is to say the noise signal is -92 dB to 0 dB ... cannot seem to testimony ... A fully test results have not been because of not the name of the laptop to connect directly into the router ...
Now it remains for the installation and testing in the city ... ... ... ...
mii-tool eth0 -A 100baseTx-FD
possible options for link speed:
100baseT4, 100baseTx-FD, 100baseTx-HD, 10baseT-FD, and 10baseT-HD.